NUQTAVIY QARSHILIK PAYVANDLASH ELEKTRODLARIGA QO‘YILADIGAN TALABLAR VA VOLFRAM–MIS KOMPOZITLARINI BAHOLASH MEZONLARI

Main Article Content

Bakhadirov, K.G.
https://orcid.org/0000-0002-5436-2205
Xakimov, S.B.
https://orcid.org/0009-0004-1817-4559

Abstract

This article investigates the functional requirements for electrode materials used in resistance spot welding and establishes evaluation criteria for assessing the suitability of tungsten–copper (W–Cu) composites for such applications. The primary objective of the study is to systematize the degradation mechanisms of welding electrodes, identify the main factors influencing their operational performance, and scientifically evaluate the potential application of W–Cu composites as electrode materials. The research is based on a comparative analysis of published scientific studies addressing thermal and chemical degradation mechanisms, electrical and thermal conductivity, high-temperature strength, wear resistance, and chemical passivity of electrode materials. Five principal functional requirements were identified, and the physical and mechanical properties of copper alloys and tungsten–copper composites were systematically compared. The results indicate that the electrical conductivity of copper alloys ranges from 78% to 88% of the International Annealed Copper Standard, whereas the maximum reported conductivity of W–Cu composites reaches 58.6%. Nevertheless, tungsten–copper composites exhibit higher hardness at room temperature, with values of 238 HV or above for certain compositions. However, the analysis revealed a lack of verified experimental data concerning high-temperature hardness, electrical contact resistance against steel, chemical interactions with zinc, and electrode service life. The findings demonstrate that additional experimental investigations are required before the application of W–Cu composites as resistance spot welding electrodes can be scientifically justified. The results provide a basis for selecting electrode materials, evaluating their operational characteristics, and developing experimental testing programs for advanced composite materials.

Downloads

Download data is not yet available.

Article Details

Section

Mining, Metallurgy, and Manufacturing Industry

Author Biographies

Bakhadirov, K.G., Tashkent State Technical University named after Islam Karimov, Materials Science department

DSc, Tashkent State Technical University named after Islam Karimov, Professor at Materials Science department

Xakimov, S.B., Tashkent State Technical University named after Islam Karimov, Department of Materials Science

PhD student, Department of Materials Science, Tashkent State Technical University named after Islam Karimov

How to Cite

Bakhadirov, K. G., & Xakimov, S. B. ugli. (2026). REQUIREMENTS FOR RESISTANCE SPOT WELDING ELECTRODES AND EVALUATION CRITERIA FOR TUNGSTEN–COPPER COMPOSITES. Digital Technologies in Industry, 4(4). https://doi.org/10.70769/3030-3214.SRT.4.4.2026.6

References

[1] Biele, L., Schaaf, P., & Schmid, F. (2021). Method for contact resistance determination of copper during fast temperature changes. Journal of Materials Science. https://doi.org/10.1007/s10853- 020-05490-w

[2] Chen, W., Shi, Y., Dong, L., & et al. (2017). Infiltration sintering of WCu alloys from copper- coated tungsten composite powders for superior mechanical properties and arc-ablation resistance. Journal of Alloys and Compounds, 728, 196–205. https://doi.org/10.1016/j.jallcom.2017.08.164 DOI: https://doi.org/10.1016/j.jallcom.2017.08.164

[3] Chen, Y.-Y., Liu, Z., Meka, S. R., Huang, Y., & et al. (2025). Effect of interface structure on advanced bonding between tungsten-based materials and Cu alloys: A review. Tungsten, 7(3), 479–496. https://doi.org/10.1007/s42864-024-00313-w DOI: https://doi.org/10.1007/s42864-024-00313-w

[4] Franczak, K., Kwaśniewski, P., Kiesiewicz, G., Ściężor, W., Sadzikowski, M., Kordaszewski, S., Micek, P., Kuca, D., & Pestrak, R. (2025a). Investigation of electrode cap life made of new Cu– Cr–Zr copper alloys with scandium addition dedicated for resistance spot welding of galvanized steel sheets. Materials, 18(21), 4950. https://doi.org/10.3390/ma18214950 DOI: https://doi.org/10.3390/ma18214950

[5] Franczak, K., Kwaśniewski, P., Kiesiewicz, G., Ściężor, W., Sadzikowski, M., Kordaszewski, S., & Noga, P. (2025b). Research on zinc diffusion in the resistance spot welding process of galvanised steels using Cu-Sc and Cu-Zr alloy electrodes. Welding in the World, 70(7), 2643– 2658. https://doi.org/10.1007/s40194-025-02116-0 DOI: https://doi.org/10.1007/s40194-025-02116-0

[6] Hamedi, M., & Atashparva, M. (2017). A review of electrical contact resistance modeling in resistance spot welding. Welding in the World, 61(2), 269–290. https://doi.org/10.1007/s40194- 016-0419-4 DOI: https://doi.org/10.1007/s40194-016-0419-4

[7] Hou, C., Song, X., Tang, F., & et al. (2019). W–Cu composites with submicron- and nanostructures: Progress and challenges. NPG Asia Materials, 11, 74. https://doi.org/10.1038/s41427-019-0179-x DOI: https://doi.org/10.1038/s41427-019-0179-x

[8] Jia, Y., Guo, L., Li, W., Zhang, S., Shi, X., & Yin, S. (2026). Recent development of oxide dispersion-strengthened copper alloys for application in nuclear fusion. Journal of Nuclear Engineering, 7(1), 10. https://doi.org/10.3390/jne7010010 DOI: https://doi.org/10.3390/jne7010010

[9] Kim, Y. D., Oh, N. L., Oh, S. T., & et al. (2001). Thermal conductivity of W–Cu composites at various temperatures. Materials Letters, 51, 420–424. DOI: https://doi.org/10.1016/S0167-577X(01)00330-5

[10] Liu, J. K., Wang, K. F., Chou, K. C., & et al. (2020). Fabrication of ultrafine W–Cu composite powders and its sintering behavior. Journal of Materials Research and Technology, 9, 2154–2163. https://doi.org/10.1016/j.jmrt.2019.12.046 DOI: https://doi.org/10.1016/j.jmrt.2019.12.046

[11] Liu, T., Han, Y., Jia, D., & et al. (2024). Graphene-enhanced CuW composites for high-voltage circuit breaker electrical contacts. Applied Sciences, 14, 2731. https://doi.org/10.3390/app14072731 DOI: https://doi.org/10.3390/app14072731

[12] Long, W., Yan, Y., You, M., & et al. (2025). High-performance W–Cu composites preparation technology, modulation strategy and strengthening mechanism. Journal of Materials Research and Technology, 36, 3240–3260. DOI: https://doi.org/10.1016/j.jmrt.2025.04.040

[13] Lungu, M. V. (2019). Synthesis and processing techniques of tungsten copper composite powders for electrical contact materials – a review. Oriental Journal of Chemistry, 35, 491–515. https://doi.org/10.13005/ojc/350201 DOI: https://doi.org/10.13005/ojc/350201

[14] Matějíček, J. (2021). Preparation of W–Cu composites by infiltration of W skeletons – review. In METAL 2021: 30th International Conference on Metallurgy and Materials. Brno, Czech Republic. https://doi.org/10.37904/metal.2021.4248 DOI: https://doi.org/10.37904/metal.2021.4248

[15] Mondal, A., Upadhyaya, A., & Agrawal, D. (2013). Effect of heating mode and copper content on the densification of W–Cu alloys. Indian Journal of Materials Science, 2013, 603791. https://doi.org/10.1155/2013/603791 DOI: https://doi.org/10.1155/2013/603791

[16] Ouyang, M., Wang, C., Zhang, H., & et al. (2021). Effects of bonding treatment and ball milling on W–20 wt.% Cu composite powder for injection molding. Materials, 14, 1897. https://doi.org/10.3390/ma14081897 DOI: https://doi.org/10.3390/ma14081897

[17] Parker, J. D., Williams, N. T., & Holliday, R. J. (1998). Mechanisms of electrode degradation when spot welding coated steels. Science and Technology of Welding and Joining, 3, 65–74. https://doi.org/10.1179/stw.1998.3.2.65 DOI: https://doi.org/10.1179/stw.1998.3.2.65

[18] Rdzawski, Z., Kwaśniewski, P., Głuchowski, W., Łagoda, M., Maleta, M., Boczkal, S., & Franczak, K. (2023). Research on changes in microstructures and mechanical properties of welding caps as a result of their usage during resistance spot welding process. Archives of Metallurgy and Materials, 68(1), 295–306. https://doi.org/10.24425/amm.2023.141506 DOI: https://doi.org/10.24425/amm.2023.141506

[19] Safahi, H., Baniassadi, M., & Faraji, G. (2024). Processing of fully dense and high conductivity W–20Cu composite via copper melt infiltration into a pressed tungsten wire skeleton. International Journal of Refractory Metals and Hard Materials, 124, 106809. https://doi.org/10.1016/j.ijrmhm.2024.106809 DOI: https://doi.org/10.1016/j.ijrmhm.2024.106809

[20] Safahi, H., Sabour, M. R., Baniasadi, M., & et al. (2025). Fracture behavior of W–20Cu composite processed via copper melt infiltration into tungsten wire skeleton. Engineering Failure Analysis, 172, 109426. https://doi.org/10.1016/j.engfailanal.2025.109426 DOI: https://doi.org/10.1016/j.engfailanal.2025.109426

[21] Sheikhi, M., Valaee-Tale, M., Mazaheri, Y., & et al. (2024). Electrode lifetime in resistance spot welding of coated sheets: Experiments and modeling. Materials Today Communications, 38, 107903. DOI: https://doi.org/10.1016/j.mtcomm.2023.107903

[22] Tejado, E., v. Müller, A., You, J. H., & Pastor, J. Y. (2018). Evolution of mechanical performance with temperature of W/Cu and W/CuCrZr composites for fusion heat sink applications DOI: https://doi.org/10.1016/j.msea.2017.12.054